5/26/2023 0 Comments Gpu benchmark test gpu failingFor details, please refer to FAQ: How to restore BIOS setting?ī. If CPU or memory is overclocked, you can enter into the motherboard BIOS Settings page to restore the BIOS to Default Settings. It may be caused by CPU, memory, or graphics card overclockingĪ. You can uninstall the graphics card driver firstly, update the latest version of the driver in nVidia/AMD official website, or the latest version in ASUS official website. It may be due that the graphics card driver is too old. Excessive temperature inside your PC case may also cause the computer components malfunction and the graphics card will have no display output. Please make sure that the ventilation and heat dissipation inside your PC case are good. Check the temperature inside your PC case (The following example: ROG-STRIX-RTX3080-O10G-GAMING, the recommended power supply for this graphics card is 850W, so you need to install a power supply of 850W or more than 850W)ġ0. Check whether the power supply can meet the requirements of the graphics cardĬonfirm whether the power of the power supply you purchased meets the recommended power on the official website If the motherboard supports multiple PCI-E slots, you can try to install the graphics card in other PCI-E slots and try again.ĩ. If it can display normally, you can turn off the power and then re-connect the graphics card to confirm whether it is a graphics card problemĨ. If it still can't boot up and display normally, you can refer to FAQ: Troubleshooting - No Power/No Boot/No Display Turn off the computer, unplug the computer power supply, take out the graphics card, and connect the monitor signal line to the corresponding display output interface on the motherboard to check whether the display can integrate display output signals from the motherboard If your motherboard in the computer has an integrated graphics processor (internal display), please try to start the system without a graphics card If it is found that there is dust or foreign matter in the PCI-E slot of the motherboard, please clean it up in time before inserting the graphics cardħ. Confirm the dust and foreign objects in the PCI-E slot of the motherboard If the connected graphics card needs to be connected to a 6Pin or 8Pin power cord, make sure that the power cord is plugged in correctly, as shown in the figure below:Ħ. Confirm the power cord of the graphics card Please shut down the computer and unplug the computer power plug, re-install the graphics card, and check whether your graphics card is correctly installed (the golden finger part of the PCI-E interface must be completely installed in the PCIE interface)ĥ. Confirm the PCI-E interface of the graphics card (golden finger) Try to insert the external devices or cables one by one, until you find which external device or cable causes no display problemĤ. If it can display normally, maybe the problem comes from the removed external device or cable. Remove all cables connected to the motherboard, including network cables and audio cables, leaving only the display cable to ensure the displayĭ. Remove all USB devices and external cards from the motherboard, including mouse, keyboards, card reader, USB flash drive, external hard drive, other external PCI-E cards other than graphics card, etc.Ĭ. Keep the CPU, CPU cooling fan and a piece of memory that connected to the motherboardī. Please refer to following instructions to remove all external devices and re-confirmĪ. Test boot with at least external equipments Confirm that the monitor displays the output signalĬheck the wiring connection between the graphics card and the monitor, make sure that the signal cable (VGA / DVI / HDMI / DisplayPort) is connected well on the monitor end, as shown in the figure below, and make sure that the input signal of the monitor is set correctlyģ. If there is still no display, please refer to the following steps.Ģ. Please follow the guideline from your PC components(such as motherboard, graphics card, power supply, case, screen, etc.) during the installation process to confirm that the related components are assembled correctly, and the components other than the graphics card can operate normally. Confirm that the computer has been installed correctly If there is no display on the monitor or abnormality(crapped display), the following tips can help you pinpoint the issue affecting your device:ġ. No display on the monitor or abnormality(crapped display)troubleshooting
0 Comments
Leave a Reply. |